Search Results

Natural vegetable oil like rape seed oil is a potential substitute for regular fuel for diesel engines. Compared to other biogen fuels like rape seed methyl ester (RME), pure rape seed oil is neutral towards groundwater and it needs considerably less energy and additives for production. Different physical properties of rape seed oil compared to Diesel fuel are the reason why conventional Diesel engines can hardly be used satisfactorily with rape seed oil without being modified. Poor exhaust-emission behavior is caused by the incomplete combustion. Due to poor spray atomization of vegetable oil, an increased fuel entrainment in the lubricating oil, carbonization in the combustion chamber and deposits at injectors and valves are further drawbacks of injection systems designed for conventional diesel fuel. The preheating of this fuel can solve some problems.

The paper presents an application of a quasi-dimensional (QD) model for the combustion simulation in a two-stroke engine. In contrast to 0D-models the QD-models provide an opportunity to describe the development of the combustion process in dependence on the actual thermodynamic state in the combustion chamber. The QD-models enable to couple the flame propagation with the combustion chamber geometry and with the flow field. An extensive sensitivity analysis is performed for the QD-model by varying the parameters of the QD-model itself and of the operating points. The constructed QD-model is examined under various conditions (engine speed, the delivery ratio and the air to fuel ratio) and shows a good agreement with experimental results.

When developing effective exhaust emission reduction measures, a better understanding of the complex working cycle in crankcase scavenged two-stroke gasoline engines. However, in a two-stroke gasoline engine detailed measurement and analysis of combustion data requires significantly more effort, when compared to a lower speed four-stroke engine. Particularly demanding are the requirements regarding the high speed (>10,000 rpm) which inevitably goes along with heavy vibrations and high temperatures of the air cooled cylinders. Another major challenge to the measuring equipment is the increased cleaning demand of the optical sensor surface due to the two-stroke gasoline mixture. In addition, the measuring equipment has to be adapted to the small size engines. Therefore, only a fiber optical approach can deliver insight into the cylinder for analyzing the combustion performance.

This paper introduces a new measuring and analyzing method for the investigation of the spatial flame propagation in IC engines. Three optical high-speed measuring devices are connected and synchronized in order to detect the flame radiation from different perspectives via fiberoptical endoscopes. The resulting two-dimensional images provide a starting basis for the subsequent reconstruction of the three-dimensional flame geometry. The reconstruction is carried out by a newly developed software tool. The capability of the new methodology has been proven in a first test series. A one-cylinder SI engine with direct-injection is operated in both homogeneous and spray-guided stratified injection mode. Intake flow conditions and air/fuel ratio are varied in order to investigate the effects on flame spread. The volumetric flame developments are analyzed as well as the location of the combustion center in absolute coordinates.

In this paper, results of experimental and numerical investigations of stratified exhaust gas recirculation in a single-cylinder gasoline engine are presented. The engine was operated in spray guided direct injection mode. The radial exhaust gas stratification was achieved by a spatial and temporal separated intake of exhaust gas and fresh air. The spatial separation of both fluids was realized by specially shaped baffles in the inlet ports, which prevent an early mixing up to the inlet valves. The temporally separation was performed by impulse charge valves, with one for the fresh air and one for the exhaust gas. From various possible strategies for time-dependent intake of fresh air and exhaust gas, four different strategies for the exhaust gas stratification were examined.

Engines with gasoline direct injection promise an increase in efficiency mainly due to the overall lean mixture and reduced pumping losses at part load. But the near stoichiometric combustion of the stratified mixture with high combustion temperature leads to high NOx emissions. The need for expensive lean NOx catalysts in combination with complex operation strategies may reduce the advantages in efficiency significantly. The Bowl-Prechamber-Ignition (BPI) concept with flame jet ignition was developed to ignite premixed lean mixtures in DISI engines. The mainly homogeneous lean mixture leads to low combustion temperatures and subsequently to low NOx emissions. By additional EGR a further reduction of the combustion temperature is achievable. The BPI concept is realized by a prechamber spark plug and a piston bowl. The main feature of the concept is its dual injection strategy.

For spark ignition engines, the most effective way to reduce the overall fuel consumption and CO2 emissions respectively is the implementation of gasoline direct injection technology. In comparison to the current wall and air guided systems, the direct injection system of the second generation - the spray guided DI- is the most promising one with respect to fuel economy and emission. In order to exploit its full potential, a thorough combustion process development regarding injector and spark plug design and their positioning within the combustion chamber is essential. Especially multihole injectors offer many degrees of freedom with regard to the nozzle shape and spray pattern. To reduce the development work and costs necessary to identify the ideal nozzle characteristic and spray pattern, reliable CFD models are necessary.

Contemporary diesel engines are high-tech power plants that provide high torques at very good levels of efficiency. By means of modern injecting-systems such as Common-Rail Injection, combustion noise and emissions could be influenced positively as well. Diesel engine are therefore used increasingly in top-range and sports cars. Today's production ECUs have no or only very low feedback regarding the process in the combustion chamber. As long as this data is missing, the design of the maps in the ECU can only be a compromise, since production tolerances and aging processes have to be considered in advance. Disturbances in the combustion process may not be detected at all. If more knowledge about the course of combustion is provided, especially the start of combustion (SOC), various operating parameters, such as the pilot injection quantity or the beginning of current feed to the injector, could be adjusted more precisely and individually for every cylinder.

Spark ignited engines with direct injection (DISI) in fuel stratified mode promise an increase in efficiency mainly due to reduced pumping losses at part load. However, the need for expensive lean NOx catalysts may reduce this advantage. Therefore, a Bowl-Prechamber-Ignition (BPI) concept with flame jet ignition was developed to ignite premixed lean mixtures in DISI engines. It is characterised by a combination of a prechamber spark plug and a piston bowl. An important feature of the concept is its dual injection strategy. A pre injection in the inlet stroke produces a homogeneous lean mixture with an air fuel ratio of λ = 1.5 to λ = 1.7. A second injection with a small quantity of fuel is directed towards the piston bowl during the compression stroke. The enriched air fuel mixture of the piston bowl is transported by the pressure difference between main combustion chamber and prechamber into the prechamber.

A promising approach for reducing both NOx- and particulate matter emissions with low fuel consumption is the so called homogeneous charge compression ignition (HCCI) combustion process. Single-cylinder engine tests were carried out to assess the influence of several parameters on the HCCI combustion. The experiments were performed both with port fuel injection (PFI) and with direct injection (DI) under various compression ratios, intake air temperatures and EGR-rates. Special emphasis was put on the fuel composition by using different gasoline and diesel fuels as well as n-heptane. Besides engine out emissions (CO2, CO, NO, O2, HC, soot) and in-cylinder pressure indication for burning process analysis, the combustion itself was visualised using an optical probe.

The quality of mixture formation and the combustion process is of significant importance for reducing the hydrocarbon emissions of small two stroke engines. The scope of this work was to investigate the mixture conditions after the exhaust closes and after the end of combustion depending on various engine operating points. For this experimental investigation a Gas Sampling Valve (GSV) was combined with a flame ionisation detector (FID) and a CO2-analyser. Using this technique, it was possible to measure the hydrocarbon concentration after end of combustion. Furthermore the local residual gas concentration after exhaust closes was determined. To allow for a comparison of the experimental results with calculations with CFD codes, in cylinder pressure measurement and exhaust gas measurements are done additionally.

The study presented in this two part paper was focused on the influence of primary mixture formation on engine running behavior covering the areas combustion and raw emissions. Two different concepts for primary fuel atomization were utilized and compared, the standard production injector and a flash boiling injector. The spray generated by the flash boiling injector was characterized by a significant reduction in droplet size and a partial direct vaporization during the injection process by preheating the fuel inside the injector. In this study special emphasis was put on the transient process of engine start between typical cooling water temperatures of -7°C and 85°C. Various measurements and visualization techniques were applied to investigate the mixture preparation, the deposition of liquid fuel on the walls, the start of combustion, and in-cylinder and engine-out UHC emissions.

The intention of the study presented in this two part paper is to investigate the influence oalf primary mixture formation on engine running behavior, covering the areas of combustion and raw emissions. Two different concepts for primary fuel atomization were utilized and compared, the standard production injector and a flash boiling injector. The flash boiling injector is characterized by a significant reduction in droplet size and a partial direct vaporization during the injection process by preheating the fuel inside the injector. In this study special emphasis was laid on the transient process of engine start between typical cooling water temperatures of -7°C and 85°C. Various measurements and visualization techniques had been applied to investigate mixture preparation, deposition of liquid fuel on the walls, start of combustion, and in-cylinder as well as engine-out UHC emissions.

The California LEV1 II program will be introduced in the year 2003 and requires a further reduction of the exhaust emissions of passenger cars. The cold start emissions represent the main part of the total emissions of the FTP2-Cycle. Cold start emissions can be efficiently reduced by injecting secondary air (SA) in the exhaust port making compliance with the most stringent standards possible. The thermochemical conditions (mixing rate and temperature of secondary air and exhaust gas, exhaust gas composition, etc) prevailing in the exhaust system are described in this paper. This provides knowledge of the conditions for auto ignition of the mixture within the exhaust manifold. The thus established exothermal reaction (exhaust gas post-combustion) results in a shorter time to light-off temperature of the catalyst. The mechanisms of this combustion are studied at different engine idle conditions.

The spray propagation and disintegration is investigated in a pressure chamber. With Particle Image Velocimetry the direction and velocity of both, fuel droplets and induced gas flow are detected. By means of shadow photographs the spray cone geometry is visualized. To verify the predictions made of the measurements mentioned above and to rate the quality of the tuning of the parameters in-cylinder gas flow, injection pressure, position of Injector and position of spark plug under real engine conditions, a fast gas sampling valve is used in three different engines. The in-cylinder gas temperature and the soot concentration are measured crank angle resolved by means of the Two-Colour-Method in a 1-cylinder GDI-engine. The soot concentration and temperature show the influence of the injection pressure on emissions like soot and nitric oxide.

The focus of this work was to determine the influence of spray targeting on temperature distributions, combustion progress and unburned hydrocarbon (HC) emissions at cold operating conditions, and to show the capability of model and full engine tests adapted for different measurement techniques. A comprehensive study applying endoscopic visualization, infrared thermography, combustion and emission measurements was carried out in a 4-stroke 4-cylinder 16-valve production engine with intake port injection during different engine operating conditions including injection angle and timing. In addition 2D visualization and PIV measurements were performed in a back-to-back model test section with good optical access to the intake manifold and the combustion chamber. The measurements in both set ups were in good agreement and show that model tests could lead to useful findings for a real engine.

In this work a new concept for GDI engines is presented. Concerning a stable ignition a main goal of the so called Bowl-Pre-chamber-Ignition (BPI) process is to reduce the influence of varying flow and spray effects. The characteristic signs of the concept are the dual direct injection, a centrally arranged piston bowl and the special pre-chamber spark plug, that partly dips into the bowl at TDC. During that process most fuel is injected early (intake stroke) into the intake manifold or directly into the cylinder to form a homogeneous pre-mixture. Later in the compression stroke, only a small amount of fuel is injected into the piston bowl. So formed locally stratified charge mixture is transported by the piston bowl to the pre-chamber-spark plug, the pre-chamber dips into the bowl and the mixture flows directly to the spark plug electrode. The result is a very stable lean combustion.

Optical measurement technique became more and more common for the last few years. Especially optical fibre technique is often used to detect flame propagation. With optical sensors the ignition process can be investigated with high temporal and spatial resolution. An in-cylinder optical sensor has been developed and tested to analyze the ignition of mixture and luminous emission of burning gas. The sensor consists of eight optical probes fitted in a conventional spark plug. The results show good correlation between measured luminosity and combustion parameters such as load, engine speed, ignition timing and air-fuel mixture ratio. A correlation between development of light intensity and pressure was found. For evaluation of light signals different analysis methods are presented. Furthermore it is shown that the luminosity of the flame can be used to control the combustion process.

A multi-optical fiber technique is presented, which enables one to detect the flame propagation during non-knocking and knocking conditions in real production engines. The measurement technique is appropriate to detect knock onset locations and to describe the propagation of knocking reaction fronts. With this knowledge, the combustion chamber shape can be optimized, leading to a better knock resistance and higher combustion efficiencies. Results of flame propagation under non-knocking and knocking engine operating conditions are presented. In addition, correlations between knock onset locations and areas in which knock damage occurs are shown for different engines. Presented are the effects of combustion chamber modifications on the combustion efficiency, based on the analysis of the optical fiber measurements.

A multi-optical fiber measurement technique is presented which can determine spatial flame propagation with a high temporal resolution. With this measurement technique it is possible to investigate the combustion process in both Diesel and SI engines. The measurement technique can also be applied for the detection of flame propagation in research engines and in actual production engines for performing analysis of special problems such as knocking combustion, combustion chamber design studies which concern flame propagation, the influence of engine parameters on flame propagation, ignition and inflammability behavior. The new measurement technique is discussed in detail and the application of optical measuring points in the combustion chamber walls is demonstrated. A special non-contacting optical transmission system has been developed for the observation of flame propagation.